Development and Characterization of Bio-based Polymer Composites Reinforced with Agricultural Waste Fibers for Sustainable Engineering Applications
Author(s): Priya Ganeshan ¹, Arvind S. Kulkarni², Neha reddy³, Manish P. Venu?
Affiliation: 1,2,3,4 Department of Chemical Engineering, R.V.R. & J.C.College of Engineering, Guntur, Andhra Pradesh, India
Page No: 26-31-
Volume issue & Publishing Year: Volume 2 Issue 6 , June-2025
Journal: International Journal of Modern Engineering and Management | IJMEM
ISSN NO: 3048-8230
DOI:
Abstract:
The increasing demand for sustainable and eco-friendly engineering materials has accelerated research into bio-based polymer composites reinforced with natural fibers derived from agricultural waste. This study focuses on the development and characterization of polymer composites utilizing rice husk and sugarcane bagasse fibers as reinforcement in a biodegradable polylactic acid (PLA) matrix. The composites were fabricated through melt blending followed by compression molding. Mechanical testing revealed that fiber loading up to 30 wt% enhanced tensile and flexural properties, with an optimal balance between strength and ductility achieved at 20 wt% fiber content. Scanning Electron Microscopy (SEM) analysis confirmed good interfacial adhesion between fibers and matrix when treated with alkaline surface modification. Thermal analysis using TGA and DSC demonstrated improved thermal stability compared to neat PLA, while water absorption tests highlighted the need for further surface treatments to reduce hydrophilicity. The results indicate that agricultural waste fibers can serve as effective, low-cost reinforcement for bio-based polymer composites, offering a viable path toward sustainable engineering materials with reduced environmental impact.
Keywords:
Bio-based polymer composites, agricultural waste fibers, rice husk, sugarcane bagasse, mechanical properties, sustainability.
Reference:
[1] R. Kumar, S. Sharma, and P. Singh, “Effect of sintering temperature on mechanical properties of alumina ceramics,” Ceram. Int., vol. 45, no. 2, pp. 1556–1564, 2019.
[2] J. Zhang, L. Wang, and Y. Liu, “Microstructural evolution and mechanical behavior of zirconia ceramics sintered at different temperatures,” J. Eur. Ceram. Soc., vol. 40, no. 10, pp. 3493–3502, 2020.
[3] M. A. Ali and S. A. Khan, “Influence of particle size and sintering temperature on densification of alumina-based composites,” Mater. Sci. Eng. A, vol. 658, pp. 233–239, 2016.
[4] D. Singh and A. Kumar, “Thermal conductivity and hardness studies of sintered ceramics,” J. Mater. Sci., vol. 52, no. 4, pp. 2345–2354, 2017.
[5] P. S. Rana and T. Mukhopadhyay, “Effect of sintering parameters on microstructure and properties of SiC ceramics,” Ceram. Int., vol. 44, no. 9, pp. 11330–11337, 2018.
[6] V. R. Raj and K. S. Rao, “Optimization of sintering temperature for improved mechanical properties of bio-ceramics,” Ceram. Int., vol. 43, no. 5, pp. 4113–4121, 2017.
[7] S. Kumar and R. Singh, “Microstructural characterization of sintered zirconia composites,” Mater. Chem. Phys., vol. 190, pp. 62–69, 2017.
[8] A. Ghosh, S. Bhattacharya, and P. Saha, “Effect of fiber reinforcement on mechanical behavior of composite materials,” Compos. Struct., vol. 154, pp. 323–332, 2016.
[9] L. Chen, M. Zhang, and X. Wu, “Grain growth mechanisms in sintered ceramics,” J. Mater. Res., vol. 33, no. 12, pp. 2034–2044, 2018.
[10] R. S. Bhatti and A. Kumar, “Mechanical and thermal properties of ceramic composites: A review,” J. Am. Ceram. Soc., vol. 101, no. 1, pp. 5–25, 2018.
[11] T. Zhang, Y. Sun, and J. Wang, “Thermogravimetric analysis of composite ceramics,” Thermochim. Acta, vol. 675, pp. 97–104, 2019.
[12] P. J. Ramírez, F. García, and C. Pérez, “Alkali treatment of natural fibers for composites: Effects on properties,” Mater. Today Commun., vol. 22, p. 100837, 2020.
[13] M. N. Islam, “Surface modification of natural fibers for improved adhesion in polymer composites,” Compos. Interfaces, vol. 27, no. 2, pp. 141–154, 2020.
[14] H. S. Lee and J. Y. Park, “Thermal and mechanical properties of PLA composites reinforced with agricultural waste fibers,” J. Appl. Polym. Sci., vol. 135, no. 20, p. 46420, 2018.
[15] N. Singh and S. S. Rana, “Impact of fiber length and content on properties of natural fiber composites,” Mater. Today: Proc., vol. 20, pp. 357–364, 2019.
[16] M. L. Agrawal and R. P. Singh, “Influence of alkali treatment on fiber surface morphology,” Int. J. Polym. Anal. Charact., vol. 25, no. 5, pp. 429–438, 2020.
[17] J. S. Lee, B. H. Kim, and S. J. Cho, “Effect of chemical treatment on natural fiber-polymer interfacial bonding,” Compos. Part B: Eng., vol. 169, pp. 226–234, 2019.
[18] K. Y. Rhee and W. T. Kim, “Mechanical behavior of hybrid composites reinforced with natural fibers,” Compos. Struct., vol. 214, pp. 306–313, 2019.
[19] S. S. Shukla and R. K. Sharma, “Thermal stability of polymer composites reinforced with natural fibers,” J. Therm. Anal. Calorim., vol. 140, no. 5, pp. 1727–1735, 2020.
[20] P. K. Singh, M. R. Prasad, and A. K. Singh, “Influence of sintering temperature on mechanical and thermal properties of ceramic composites,” Ceram. Int., vol. 46, no. 1, pp. 157–165, 2020.
[21] M. N. Rahman, “Processing and characterization of natural fiber composites: A review,” J. Compos. Mater., vol. 54, no. 2, pp. 185–204, 2020.
[22] S. P. Singh and V. K. Srivastava, “Development of sustainable composites using agro-waste fibers,” J. Clean. Prod., vol. 214, pp. 644–655, 2019.
[23] A. T. Nguyen and J. Y. Lee, “Thermomechanical properties of fiber-reinforced biocomposites,” Mater. Sci. Eng. A, vol. 760, p. 138020, 2019.
[24] B. J. Kim, J. H. Choi, and H. G. Lee, “Microstructural characterization of polymer composites with natural fiber reinforcement,” Mater. Charact., vol. 161, p. 110170, 2020.
[25] R. Sharma and M. S. Singh, “Influence of fiber treatment on mechanical properties of natural fiber composites,” Compos. Sci. Technol., vol. 183, p. 107812, 2019.
[26] A. K. Singh and P. K. Verma, “Effect of sintering process on densification and mechanical properties of ceramics,” Ceram. Int., vol. 45, no. 6, pp. 7432–7439, 2019.
[27] J. H. Park, S. W. Lee, and K. T. Kim, “Evaluation of mechanical and thermal properties of hybrid natural fiber composites,” J. Mater. Res. Technol., vol. 8, no. 4, pp. 3991–3999, 2020.